Citizen Systems CBM-910 Manuel d'utilisateur

DOT MATRIX PRINTERCBM-910Type II

— 7 —9. CHARACTER CODE TABLE ... 479.1 ASCII + 910 Emulation (International) ...

— 8 —1. INTRODUCTIONThe CBM-910II is a dot-impact printer widely usable with various data communicationterminals and measurement terminals.This print

— 9 —Model NameNumber of columns24: 24 columns/144 dots40: 40 columns/180 dotsInterfaceP: Parallel (Conformity to Centronics)R: Serial (RS-232C)CBM-91

— 10 —Item CBM-910II-24 CBM-910II-401 Printing method Dot matrix2 Printing direction One-way printing3 Character configuration (W × H) (5 + 1) × 8 (4

— 11 —(8) Print coverUpper coverLower cover(2) Power switch(5) LF switch(6) SEL switch(4) SEL lamp(3) Power lamp(1) DC jack(7) Interface connector3. E

— 12 —3.2 Part Descriptions(1) DC jack Insert the output plug of the AC adapter attached.(2) Power switch When switched ON, power is supplied to the

— 13 —4. OPERATIONS4.1 Connection of the AC Adapter(1) Ensure that the power switch is OFF.(2) Insert the output plug of the AC adapter into the DC

— 14 —Protruding4.2 Setting of the Printer Cover(1) Hold the protruding section at the rear of the printer cover and lift in the directionindicated.(

— 15 —KnobPlatenPrinting head4.3 Setting Ribbon Cassettes(1) Remove the printer cover turning OFF the printer.(2) Press down on the Ribbon cassette w

— 16 —OK NO GOOD NO GOODOKPaper holder4.4 Setting Paper(1) Remove the printer cover.(2) Ensure that the end of the paper is straight or incline as in

— 1 —This printer conforms to the following Standards:Low Voltage Directive 73/23/EEC, 93/68/EEC and the EMC Directive 89/336/EEC, 92/31/EEC,93/68/EEC

— 17 —* SPECIAL REMARKS CONCERNING PAPERSHAPE: The beginning of winding (end part of the inside diameter) should satisfy the following (Referto Drawin

— 18 —31 32 33 34 35 36 37 38 1234567839 3A 3B 3C 3D 3E 3F 40 9*+,-./@41 42 43 44 45 46 47 48 ABCDEFGH49 4A 4B 4C 4D 4E 4F 50 IJKLMNOP51 52 53 54 55 5

— 19 —NOTEBefore turning the printer power on, restore the DIP switch No. 4 to the former position.4.6 Memory Switch Setting<Memory Switch Initial

— 20 —<Contents of Memory Switch Setting>In square brackets ([ ]), choose one of the options for each setting item. Itemmarked * is the default

— 21 —7. BUSY (Busy signal clear timing)[*Standard, CBM-910] *1Selects the clear timing of Busy signal for parallel I/F.Standard: Clears after confir

— 22 —4.8 General Remarks(1) Do not print without ink ribbon properly provided. It may cause damage on theprint head.(2) Replace the ink ribbon with

— 23 —Pin Signal Name Pin Signal Name1 STB 19 TWISTED PAIR GND2DATA 1 203DATA 2 214DATA 3 225DATA 4 236DATA 5 247DATA 6 258DATA 7 269DATA 8 2710 ACK 2

— 24 —POWERDATASTBT1DATA DATA DATAT2BUSYACKT3T1: 1.6 µs MINT2: 500 µS MINT3: 10 µs TYPT4: 5 µs TYPT5: 5 µS TYP5.3 Description of Input/Output Signals

— 25 —DATAVCC3.3k< HOST SIDE > < PRINTER SIDE >(HC04 or equivalent)STBACK BUSY P.N.E.OUTPUT SIGNALRESETVCC3.3k100102 471(HC04 or equivalen

— 26 —6. SERIAL INTERFACE6.1 Specifications(1) Synchronization: Asynchronous(2) Baud rate1200, 2400, 4800, 9600, 19200 Baud/sec (User selection)(3)

— 2 —FCC Compliance Statement for American UsersThis equipment has been tested and found to comply with the limits for a Class B digital device,pursua

— 27 —6.2 Connector Pin Assignment*1: Enable/Disable of RESET signal can be selected by DIP switch No. 3.In addition, changing the internal resistanc

— 28 —MarkSpacetb0, b1, b2 • • • • •(1) (2) (3)(1) Start bit (1 bit)(2) Data bit (8 bits)(3) Stop bit (more than 1 bit)6.3 Description of Inp

— 29 —6.4 Electrical Characteristics(1) RS-232C I/O signals (RD/TD/DTR)• Input (RD)Mark = (−8 V): Stop bitSpace = (+8 V): Start bit• Output (TD, DTR)

— 30 —6.5 Error Detection● Communication error• Parity errorParity error occurs when parity check is specified and parity is not observed inthe even

— 31 —7. DIP SWITCH SETTING7.1 Serial Interface Type*1: A difference is developed by the emulation set by the memory switch.*2: After setting DIP sw

— 32 —7.2 Parallel Interface Type*: Difference may occur in accordance with the emulation set by the memory switch.After setting DIP switch No. 4 to

— 33 —8. PRINT CONTROL FUNCTION8.1 List of Control CodesCode(Hexadecimal)LF 0A Line feed after print O*1 O*1CR 0D Carriage return and line feed O*1

— 34 —8.2 Control Code Details(1) Command for Line Feed After Printing (CR/LF)By entering CR (0DH)/LF (0AH) codes, data in the print buffer is printe

— 35 —2. Laterally enlarged letter assignment (SO/RS) command:With SO (0EH)/RS (1EH) codes input in any columns, the data following areprinted in prin

— 36 —(4) Inverted Letter Assignment (DC2) CommandWhen data are input with DC2 (12H) attached at the beginning of a line (invalidwhen attached to any

— 1 —< GENERAL PRECAUTIONS >1. Prior to using the printer, be sure to read this User’s Manual thoroughly. Please keep ithandy so that you can r

— 37 —(7) Continuous Paper Feed Assignment (ESC + “B” + n) CommandWith ESC (1BH) +“B” (42H) + n code input, continuous paper feed at n-dot line isexec

— 38 —(10) Sentence Registration (ESC + “/” + n) CommandWith input of ESC (1BH) + “/” (2FH) + n + ‘registered sentence’ code, 24 (40)-bytesdata follow

— 39 —<Registered State> It is pen12345678<Printing Result>Is this a pen ?It is a pen(Printed out with ESC + “!” + 1)(12) Character Regist

— 40 —[Method of data transmission]d-1) Single character registrationSelect the address to be defined (character code) from among 20H toFFH and design

— 41 —2. For 40-column modelIn 910 emulation (ESC + “&” + C1 + A1 + A2)In 3110 emulation (ESC + “&” + A1 + A2)With ESC (1BH) + ”&” (26H) +

— 42 —In 3110 emulationFollowing ESC + & + 01 (Note) + 41H + 42Hsending data 80H, 00H, 81H, 00H, 89H, 00H, 89H, 00H, FFH00H, 89H, 00H, A9H, 40H, 8

— 43 —(13) Registered Letter Valid/Invalid (ESC + “%” + n) CommandWhether a registered pattern is valid or invalid is set with ESC (1BH) + ”%”(25H) +

— 44 —(14) Bit Image Printing (ESC +“K”+ n1 + n2 + n3) CommandWith ESC (1BH) + K (4BH) + n1 + n2 + n3 code being input, conversion fromText mode into

— 45 —(15) ×4 Enlarged Letter Assignment (FS + “W” + 1) CommandFS (1CH) + “W” (57H) + 1 (01H) code input, ×4 enlarged letters are assigned.Data follow

— 46 —NOTEWhen the set value is outside the specified range, writing to memory is not carried out.n1 Function n2 Content of Setting0Select internation

— 2 —SAFETY PRECAUTIONS -WHICH SHOULD BE STRICTLY OBSERVEDIn order to prevent injury hazard to operators, third parties or damage to property, special

— 47 —9. CHARACTER CODE TABLE9.1 ASCII + 910 Emulation (International)9.2 910 Emulation (Japan)

— 48 —9.3 Codepage PC437 (USA, Standard Europe)9.4 Katakana

— 49 —9.5 Codepage PC858 (Multilingual)9.6 Codepage PC860 (Portuguese)

— 50 —9.7 Codepage PC863 (Canadian-French)9.8 Codepage PC865 (Nordic)

— 51 —9.9 Codepage PC852 (Eastern Europe)9.10 Codepage PC866 (Russian)

— 52 —9.11 Codepage PC857 (Turkish)9.12 Codepage WPC1252 (Windows Latin1)

— 53 —9.13 Codepage PC864 (Arabic)9.14 Codepage PC869 (Greek)

— 54 —9.15 International Character Code Table

— 55 —10. EXTERNAL DIMENSIONS80 Dia. Paper Roll60 Dia. Paper Roll

— 56 —Note 1: Drawings above indicate the bottom and side views of CBM-910 main body.Note 2: The wall hanging screw head shall be below 3 mm long.2 R

— 3 —● Never handle the printer in the manners described below; otherwise, it may bedamaged, get out of order or overheated, possibly causing smoke, f

— 57 —

1.04E-0503 Printed in Japan

— 4 —● Do not use or store the printer in a place exposed to heat of fire, moisture or directsunlight, or in a place where the prescribed operating te

— 5 —Do not handle the equipment in the following manners, because problems may result.● Do not print when there is no recording paper or ink ribbon s

— 6 —THE TABLE OF CONTENTS1. INTRODUCTION ..................... 81.1 Features ...